MINDMAN 2/2 way piston series

MGA for water. air and higher temp. Forged brass body, IP65 100% ED coil, PTB approval EExmIIT4 coil, Pipe: G3/8, G1/2. Features: Forged brass body IP65 100% ED coil PTB approval EExmIIT4 coil MGS for

MGA

for water. air and higher temp. Forged brass body, IP65 100% ED coil, PTB approval EExmIIT4 coil, Pipe: G3/8, G1/2.

Features:

  • Forged brass body
  • IP65 100% ED coil
  • PTB approval EExmIIT4 coil

MGS

for water. air and higher temp. Forged brass body, IP65 100% ED coil, PTB approval EExmIIT4 coil, Pipe: G3/8, G1/2.

Features:

  • Forged brass body
  • IP65 100% ED coil
  • PTB approval EExmIIT4 coil

MWA

IP65 waterproof coil Ex coil is EExmⅡT4 PTB approval. Pipe: G3/8, G1/2, G3/4, G1, G1 1/4, G1 1/2, G2.
Features:
  • IP65 waterproof coil
  • Ex coil is EExmⅡT4 PTB approval.
  • Ambient temp: -15~50℃
  • Voltage tolerance: ±8%
  • Installing position is free.(You’d better put the coil upright.)

MWH

IP65 waterproof coil Ex coil is EExmⅡT4 PTB approval. Pipe: G3/8, G1/2,G3/4, G1, G1 1/4, G1 1/2, G2.

Features:
  • IP65 waterproof coil
  • Ex coil is EExmⅡT4 PTB approval.
  • Ambient temp: -15~50℃
  • Voltage tolerance: ±8%
  • Installing position is free.(You’d better put the coil upright.)

MWS

IP65 waterproof coil Ex coil is EExmⅡT4 PTB approval. Pipe: G3/8, G1/2,G3/4, G1, G1 1/4, G1 1/2, G2.
Features:
  • IP65 waterproof coil
  • Ex coil is EExmⅡT4 PTB approval.
  • Ambient temp: -15~50℃
  • Voltage tolerance: ±8%
  • Installing position is free.(You’d better put the coil upright.)

MYA

Y type forged brass body, IP65 100% ED coil, PTB approval EExmIIT4 coil, Pipe: G3/8, G1/2.

Features:

  • Y type forged brass body
  • IP65 100% ED coil
  • PTB approval EExmIIT4 coil

MYS

Y type forged brass body, IP65 100% ED coil, PTB approval EExmIIT4 coil, Pipe: G3/8, G1/2.

Features:

  • Y type forged brass body
  • IP65 100% ED coil
  • PTB approval EExmIIT4 coil

MSUS

Normally closed / Normally open,Available fluid: Water, air, steam, gas, vacuum & Light oil.

Features:

  • Direct acting,conduct and normally closed / normally open.
  • Able to be operated under no differential pressure.
  • Acceptable for customization Viton (130°C), Silicone (130°C) and EPDM (130°C) for seal plug.
  • AC voltage tolerance: ±10%. DC voltage tolerance: ±1%.
  • Before pipelining, the pipe line must be very clean without any contaminants or impurity.
  • To extend the lifetime, Y-line filter should be installed in the front end of solenoid valve.
  • It should be installed horizontally; vertical installation is not advisable.

Specification:

Body Stainless steel
Coil Special copper wire (H)
Tube Stainless steel
Spring Stainless steel
Core Stainless steel
Plug NBR, Viton, Silicon, PTFE
Washer NBR, PTFE

 

MUAO

2-WAY normally closed solenoid valve.Available fluid: Water, air & oil.
Features:
  • Multiplex acting, piston guide, conductive normal close.
  • AC voltage tolerance: ±10%. DC voltage tolerance: ±1%
  • Applied to sand blasting machine and high-pressure air and oil injection system
  • Min pressure to open: over 0.05 MPa.
  • Before pipelining, the pipe line must be very clean without any contaminants or impurity.
  • To extend the lifetime, Y-line filter should be installed in the front end of solenoid valve.
  • It should be installed horizontally; vertical installation is not advisable

Specification:

Body Brass
Coil Special copper wire (H)
Piston Brass
Tube Stainless steel
Spring Stainless steel
Core Stainless steel
Plug NBR

MUAW

2-way normally closed solenoid valve.Available fluid: Water, air.
Features:
  • MUAW series is multiplex acting, piston guide, conductive and normal close.
  • AC voltage tolerance: ±10%. DC voltage tolerance: ±1%.
  • Min pressure to open: over 0.05~0.1 MPa.
  • Before pipelining, the pipe line must be very clean without any contaminants or impurity.
  • To extend the lifetime, Y-line filter should be installed in the front end of solenoid valve.
  • It should be installed horizontally; vertical installation is not advisable.
Specification:
Body Cast bronze
Coil Special copper wire (H)
Piston Brass
Tube Stainless steel
Spring Stainless steel
Core Stainless steel
Plug PTFE+15%GF
Bonnet / nut NBR

 

MUS

2-way normally closed solenoid valve.Available fluid: Water, air, steam & heavy oil.

Features:

  • MUS/MUS-F series is multiplex-drive, piston guide, connected normal close.
  • Acceptable for customization Viton (130°C) , Silicone (130°C) and EPDM (130°C) for seal plug.
  • Flange: JIS 10K (Option: ANSI 150LB or PN-16).
  • AC voltage tolerance: ±10%. DC voltage tolerance: ±1%
  • Min pressure to open 0.05 MPa (over 1 1/4″ is 0.1 MPa).
  • Before pipelining, the pipe line must be very clean without any contaminants or impurity.
  • To extend the lifetime, Y-line filter should be installed in the front end of solenoid valve.
  • It should be installed horizontally; vertical installation is not advisable.

Specification:

Body Cast bronze
Coil Special copper wire (H)
Piston Brass
Tube Stainless steel
Spring Stainless steel
Core Stainless steel
Plug PTFE+15%GF
Bonnet / nut PTFE

MUS-F

2-way normally closed solenoid valve.Available fluid: Water, air, steam & heavy oil.
Features:
  • 2-WAY normally closed solenoid valve.
  • MUSF series is multiplex-drive, piston guide, conductive normal close.
  • Other voltage of AC/DC available when required.
  • The standard product fluid temperature is 185℃(PTFE).
  • Flange end:JIS 10K, ANSI 150LB or PN-16.
  • AC Voltage tolerance: ±10%. DC Voltage tolerance: ±1%.

Specification:

Body FC-20
Coil Special copper wire (H)
Piston Brass
Tube Stainless steel
Spring Stainless steel
Core Stainless steel
Plug TFE
Bonnet / nut PTFE

MSUW-F

2-WAY normally closed solenoid valve.Available fluid: Water, air & light oil.
Features:
  • MSUW-F series is direct multiplex acting, connected diaphragm, normal close.
  • Able to be operated under low pressure.
  • Acceptable for customization Viton (130°C) , Silicone (130°C) and EPDM (130°C) for seal plug and diaphragm.
  • Flange: JIS 10K (Option: ANSI 150LB or PN-16)
  • AC voltage tolerance: ±10%. DC voltage tolerance: ±1%.
  • Flange end:JIS 10K, ANSI 150LB or PN-16.
  • Before pipelining, the pipe line must be very clean without any contaminants or impurity.
  • To extend the lifetime, Y-line filter should be installed in the front end of solenoid valve.
  • It should be installed horizontally; vertical installation is not advisable.

Specification:

Body CF8M #316
Coil Special copper wire (H)
Tube Stainless steel
Fixed steel Stainless steel
Spring Stainless steel
Plug NBR, Viton, Silicon
Diaphragm NBR, Viton, Silicon

MUPS

2-way normally closed solenoid valve.Available fluid: Water, air, steam & light oil.
Features:
  • MUPS series is multiplex acting, piston guide, conductive normal close.
  • Acceptable for customization Viton , Silicone and EPDM for seal plug.
  • Minimum pressure to open: over 0.05 MPa.
  • AC voltage tolerance: ±10%. DC voltage tolerance: ±1%.
  • Before pipelining, the pipe line must be very clean without any contaminants or impurity.
  • To extend the lifetime, Y-line filter should be installed in the front end of solenoid valve.
  • It should be installed horizontally; vertical installation is not advisable.

Specification:

Body Forged brass
Coil Special copper wire (H)
Piston Brass
Tube Stainless steel
Spring Stainless steel
Core Stainless steel
Plug PTFE
Bonnet / nut PTFE
No reprinting without permission:Ruhong Seiko (Xiamen) Electronics Technology Co.,Ltd. » MINDMAN 2/2 way piston series
Share To:
Pneumatic
Components
Hydrulic
Components元件
Transmission
Equipment
Instruments
Apparatuses