MINDMAN 2/2 way diaphragm series

MED Forged brass body, pressure forming S.S. plate, for water. air, Pipe: G1/4, G3/8, G1/2. MGD Forged brass body, N.C., for water, air, gas etc. IP65 100% ED coil. EExmIIT4 PTB approval coil. Pipe: G

MED

Forged brass body, pressure forming S.S. plate, for water. air, Pipe: G1/4, G3/8, G1/2.

MGD

Forged brass body, N.C., for water, air, gas etc. IP65 100% ED coil. EExmIIT4 PTB approval coil. Pipe: G3/8, G1/2, G3/4, G1, G1 1/4, G1 1/2, G2.
Features:
  • IP65 100% ED coil
  • PTB approval EExmIIT4 coil

MPD

PAD (Nylon) body, N.C., O.P.D. 0.2 bar, PAK (Nylon) body, N.C., O.P.D. 0 bar, for water, special fluids etc.Pipe: G1/2, G3/4, G1.

Features:

  • IP65 waterproof coil.
  • Continuous cycle,100% ED.
  • Ambient temperature:-5~+50°c(No freezing).

MPK

PA (Nylon) body, N.C., O.P.D. 0 bar, for water, special fluids etc. Pipe: G1/2, G3/4, G1.

Features:

  • IP65 waterproof coil.
  • Continuous cycle,100% ED.
  • Ambient temperature:-5~+50°c(No freezing).

MUSD

SCS14 body, 2/2 way N.C. Available fluid: Air, gas, water, light oil.Pipe: G1/2.
Features:
  • IP65 waterproof coil.
  • Continuous cycle, 100% ED.
  • Ex coil is EExmⅡT4 PTB approval.

MWD

Forged brass body, 2/2 way N.C. Available fluid: Air, water, gas.Pipe: G3/8, G1/2, G3/4, G1, G1 1/4, G 1 1/2, G2.
Features:
  • IP65 waterproof coil.
  • Continuous cycle, 100% ED.
  • Ex coil is EExmⅡT4 PTB approval.

MWK

Forged brass body, 2/2 way N.C. Available fluid: Air, water, gas, light oil, vacuum. Pipe: G3/8, G1/2, G3/4, G1, G1 1/4, G 1 1/2, G2.
Features:
  • IP65 waterproof coil.
  • Continuous cycle, 100% ED.
  • Ex coil is EExmⅡT4 PTB approval.

MUDC

2 way normally closed, Available fluid: Hydrochloric acid, sulfuric acid.
Features:
  • Direct acting, conductive to diaphragm, normal closed.
  • Can be operated under no differential pressure.
  • PVC valve body is corrosion-resistant (pH 3~11).
  • PTFE valve body is corrosion-resistant (pH 0~14).
  • AC voltage tolerance: ±10%. DC voltage tolerance: ±1%
  • Before pipelining, the pipe line must be very clean without any contaminants or impurity.
  • To extend the lifetime, Y-line filter should be installed in the front end of solenoid valve.
  • It should be installed horizontally; vertical installation is not advisable.

Specification:

Body MUDC: PVC、MUDC-TF: PTEF
Coil Special copper wire (H)
Tube Stainless steel
Spring Stainless steel
Core Stainless steel
Washer Synthetic rubber
Diaphragm PTFE

MUW

2-way normally closed solenoid valve.Available fluid: Water, air & light oil.
Features:
  • Direct and multiplex acting, connected diaphragm, normal close.
  • Can be operated directly under low pressure.
  • Acceptable for customization Viton (130°C) , Silicone (130°C) and EPDM (130°C) for seal plug and diaphragm.
  • AC voltage tolerance: ±10%. DC voltage tolerance: ±1%.
  • Pipes must be washed neat and clean before fitted.
  • A Y-STRAINER has to be installed in the front of solenoid valve, that is best for long life.
  • It should be installed horizontally; vertical installation is not advisable.

Specification:

Body Forge brass / Cast bronze
Coil Special copper wire (H)
Tube Stainless steel
Spring Stainless steel
Core Stainless steel
Plug NBR, viton, silicon

MUW-NO

2-WAY normally open solenoid valve.Available fluid: Water, air, gas & vacuum.
Features:
  • Direct and multiplex acting, connected diaphragm, normal open.
  • Can be operated directly under low pressure.
  • Acceptable for customization Viton (130°C) , Silicone (130°C) and EPDM (130°C) for seal plug and diaphragm.
  • AC voltage tolerance: ±10%. DC voltage tolerance: ±1%
  • Before pipelining, the pipe line must be very clean without any contaminants or impurity.
  • To extend the lifetime, Y-line filter should be installed in the front end of solenoid valve.
  • It should be installed horizontally; vertical installation is not advisable.

Specification:

Body Forge brass / Cast bronze
Coil Special copper wire (H)
Tube Stainless steel
Spring Stainless steel
Core Stainless steel
Plug NBR, viton, silicon
Diaphragm NBR, viton, silicon

MUG

2-way normally closed solenoid valve.Available fluid: Gas.
Features:
  • Direct and multiplex acting, connected diaphragm,  normal close.
  • Can be operated under no differential pressure.
  • AC voltage tolerance: ±10%. DC voltage tolerance: ±1%.
  • Before pipelining, the pipe line must be very clean without any contaminants or impurity.
  • To extend the lifetime, Y-line filter should be installed in the front end of solenoid valve.
  • It should be installed horizontally; vertical installation is not advisable.

Specification:

Body Forge brass / Cast bronze
Coil Special copper wire (H)
Tube Stainless steel
Spring Stainless steel
Core Stainless steel
Plug NBR
Diaphragm NBR for gas use

 

MUV

2-way normally closed solenoid valve.Available fluid: vacuum.

Features:

  • 2-WAY normally closed solenoid valve.
  • MUG/V series is pilot diaphragm drive,connected to diaphragm, normal close.
  • Can be operated directly without pressure.
  • Other voltage of AC/DC available when required.
  • Installation: Mountable in leave position only. (Prohibition in vertical position).
  • AC Voltage tolerance: ±10%. DC Voltage tolerance: ±1%.

Specification:

Body Forge brass / Cast bronze
Coil Special copper wire (H)
Tube Stainless steel
Spring Stainless steel
Core Stainless steel
Plug NBR
Diaphragm NBR for gas use

MSUW

2-way normally closed / normally open solenoid valve.Available fluid: Water, air & light oil.
Features:
  • 2-WAY normally closed / normally open solenoid valve.
  • MSUW / MUSW-NO series is pilot diaphragm drive, normal close / normal open.
  • Valve body made of investment casting S/S 316.
  • Can be operated directly without pressure.
  • Other voltage of AC/DC available when required.
  • Viton(130℃), Silicon(130℃), NBR(80℃.).
  • AC Voltage tolerance: ±10%. DC Voltage tolerance: ±1%.

Specification:

Body Cast 316 SS (CF8M)
Coil Special copper wire (H)
Tube Stainless steel
Spring Stainless steel
Core Stainless steel
Plug NBR, viton, silicon
Diaphragm NBR, viton, silicon
Ambient temperature -5~+40℃ (No freezing)

MSUW-NO

2-way normally closed / normally open solenoid valve.Available fluid: Water, air & light oil.
Features:
  • Direct and multiplex drive, connected diaphragm, normal close / normal open.
  • Can be operated directly under low pressure.
  • Acceptable for customization Viton (130°C) , Silicone (130°C) and EPDM (130°C) for seal plug and diaphragm.
  • AC voltage tolerance: ±10%. DC voltage tolerance: ±1%.
  • Other voltage of AC/DC available when required.
  • Before pipelining, the pipe line must be very clean without any contaminants or impurity.
  • To extend the lifetime, Y-line filter should be installed in the front end of solenoid valve.
  • It should be installed horizontally; vertical installation is not advisable.

Specification:

Body Cast 316 SS (CF8M)
Coil Special copper wire (H)
Tube Stainless steel
Spring Stainless steel
Core Stainless steel
Plug NBR, viton, silicon
Diaphragm NBR, viton, silicon
Ambient temperature -5~+40℃ (No freezing)

MXCD

2-way normally closed solenoid valve, Available fluid: Water, Air, Naphtha.Pipe: 1/4, 3/8, 1/2.
Features:
  • In order to prolong operating life,it is better to allocate pipe horizontally and coil to face upward.
  • Voltage drop range is within ±10%.
  • Pressure of voltage DC is 70% of voltage AC only.
  • Combined diaophragm design assure no breaking.
  • Fluid temp.-10~+80°C(Naphtha120°C).

MXPV

2-way normally closed solenoid valve, Available fluid: Water, Air, Naphtha.Pipe: 3/8, 1/2, 3/4.
Features:
  • Diretc-acting valves are ideally suited to allocate at any angle.
  • Voltage drop range is within ±10%.
  • Pressure of voltage DC is 70% of voltage AC only.
  • Floid temp.-10~+80°C(Naphtha 120°C).

MUW-F

2-WAY normally closed / normally open solenoid valve.Available fluid: Water, air.
Features:
  • Multiplex acting, piston guiding, conductive and normal close / normal open.
  • Acceptable for customize Viton (130°C) , Silicone (130°C) and EPDM (130°C) for seal plug and diaphragm.
  • AC voltage tolerance: ±10%. DC voltage tolerance: ±1%.
  • Installation: Mountable in leave position only.
  • Before pipelining, the pipe line must be very clean without any contaminants or impurity.
  • To extend the lifetime, Y-line filter should be installed in the front end of solenoid valve.
  • It should be installed horizontally; vertical installation is not advisable

Specification:

Body FC-20
Coil Special copper wire (H)
Tube Stainless steel
Spring Stainless steel
Core Stainless steel
Plug NBR
Diaphragm NBR
No reprinting without permission:Ruhong Seiko (Xiamen) Electronics Technology Co.,Ltd. » MINDMAN 2/2 way diaphragm series
Share To:
Pneumatic
Components
Hydrulic
Components元件
Transmission
Equipment
Instruments
Apparatuses